HOW to make a duct tape  wallet menu

Shout-Out

User Tag List

Results 1 to 3 of 3
  1. #1
    Guzey's Avatar Member
    Reputation
    8
    Join Date
    Jun 2007
    Posts
    117
    Thanks G/R
    0/0
    Trade Feedback
    0 (0%)
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    HOW to make a duct tape wallet

    Step 1

    The first step is to create a large sheet of duct tape 8.5 inches by 7 inches. This is the key to any duct tape project, with a sheet of tape you can make anything! Rip a strip of tape at least 8.5 inches in length and place sticky side up on your working surface. rip a second piece of equal length and place sticky side down half way over the first strip. Fold the rest of the strip facing up over the second strip. Flip over the two strips and place a third strip sticky side down covering the remaining sticky part of the second strip. Flip the sheet again and continue extending the size of the sheet until the needed size is satisfied.

















    Step 2

    Trim the edges, fold the wallet in half and tape the sides to create a large pocket to hold bills.










    Step 3

    To create credit/business card pockets create another sheet 4 by 3.5 inches.











    Step 4

    Fold 1.5 inches over. To create two more pockets, repeat the step above and then tape the two pieces together, taping the second pocket a little lower on top of the first piece.







    Step 5

    Tape the edges of the pockets and then tape the whole piece to the large pocket. To create another pocket, leave the inside part untaped.





    Step 6


    Make a sheet of tape (as in the first step) larger than your ID card. Cut the sheet so the outside part of the frame is slightly larger than the height and width of the ID. Cut the inside .5 centimeters, (big enough you can see you picture and info, but small enough the ID can't fall through the opening. Now trim the outside so it is slightly larger in all directions than your ID. Tape three sides of this window to the inside of your wallet, or on top of the credit card holder. It'll take a some trial an error to get it right, but it will be a great addition to the wallet. When your done, the ID should be able to slide into the untaped side of the holder, and once in, not fall through the open window.












    Step 7

    Tape the completed pocket to the large pocket and again you can create an extra pocket if you wish by leaving the inside part untaped.





    Step 8

    This is the completed wallet. There are an infinite ways to personalize this design. Some ideas I've embeded in mine are coin pockets within the large bill pocket and placing flaps on the credit card holders so business cards don't fall out when the wallet gets dropped.





    Instructions written by Dustin Kirk | How To Make A Duct Tape Wallet

    HOW to make a duct tape  wallet
  2. #2
    Remahlól's Avatar !!jeULyJf8ld1
    Reputation
    538
    Join Date
    Feb 2007
    Posts
    2,254
    Thanks G/R
    0/1
    Trade Feedback
    0 (0%)
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    Well, nice share. But I'd rather **** around with my Louis Vuitton wallet.

    (300€ in the Louis Vuitton store in Verona, Italy.)
    19/5/2013

  3. #3
    joric's Avatar Member
    Reputation
    2
    Join Date
    Aug 2007
    Posts
    77
    Thanks G/R
    0/0
    Trade Feedback
    0 (0%)
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)
    lol i saw this on youtube.

Similar Threads

  1. How to Make a Character with Cool Letters
    By Cyboi in forum World of Warcraft Guides
    Replies: 62
    Last Post: 08-21-2007, 01:52 PM
  2. How to make Macro's
    By oninuva in forum World of Warcraft Guides
    Replies: 21
    Last Post: 11-20-2006, 01:02 PM
  3. How to make good Pick-Up Groups (PUG's)
    By Krazzee in forum World of Warcraft Guides
    Replies: 0
    Last Post: 06-10-2006, 07:28 PM
  4. How to make the darkmoon card: blue dragon proc without casting
    By Matt in forum World of Warcraft Guides
    Replies: 1
    Last Post: 04-17-2006, 05:17 AM
All times are GMT -5. The time now is 10:35 AM. Powered by vBulletin® Version 4.2.3
Copyright © 2025 vBulletin Solutions, Inc. All rights reserved. User Alert System provided by Advanced User Tagging (Pro) - vBulletin Mods & Addons Copyright © 2025 DragonByte Technologies Ltd.
Google Authenticator verification provided by Two-Factor Authentication (Free) - vBulletin Mods & Addons Copyright © 2025 DragonByte Technologies Ltd.
Digital Point modules: Sphinx-based search