How to update server to 2.3.3

[kuy]

Ok Here is alittle guide i made up i haven't seen any like this one so i am posting this guide ok on to the guide.

Step 1
***********************************************************
For this guide i used AC Web Ultimate Repack but i think it might work on others too.Ok Open up that folder.

Step 2
***********************************************************
Now open up the Ascent file in the repack folder and find the logonserver.confile and open it with notepad.

Step 3
*********************************************************
Ok its should look like this........
#######################################################################
# Ascent Realms Configuration File
# Last updated at revision 446 by Burlex
#######################################################################

/********************************************************************************
* How to use this config file: *
* Config files are in a block->variable->setting format. *
* A < signifies the opening of a block, the block name is expected after that. *
* After the block name, a space and then the settings sperated by = / ' '. *
* *
* e.g. *
* <block setting="0" someval = "1"> *
* *
* Comments can be in C format, e.g. /* some stuff */, with a // at the start *
* of the line, or in shell format (#). *
********************************************************************************/

# LogonDatabase Section
#
# These directives are the location of the `realms` and `accounts`
# tables.
#
# LogonDatabase.Host - The hostname that the database is located on
# LogonDatabase.Username - The username used for the mysql connection
# LogonDatabase.Password - The password used for the mysql connection
# LogonDatabase.Name - The database name
# LogonDatabase.Port - Port that MySQL listens on. Usually 3306.
# LogonDatabase.Type - Client to use. 1 = MySQL, 2 = PostgreSQL, 3 = Oracle 10g
#

<LogonDatabase Hostname = "localhost"
Username = "root"
Password = "ascent"
Name = "logon"
Port = "3306"
Type = "1">


# Host Directive
#
# This is the address that the realmlist will listen on.
# To listen on all addresses, set it to 0.0.0.0
# Default: 127.0.0.1 (localhost)
#
# Note: ISHost is the interserver communication listener.
#

<Listen Host = "0.0.0.0"
ISHost = "0.0.0.0"
RealmListPort = "3724"
ServerPort = "8093">

# Server console logging level
#
# This directive controls how much output the server will
# display in it's console. Set to 0 for none.
# 0 = Minimum; 1 = Error; 2 = Detail; 3 = Full/Debug
# Default: 3
#

<LogLevel Screen = "0"
File = "-1">

# Account Refresh Time
#
# This controls on which time interval accounts gets
# refreshed. (In seconds)
# Default = 600
#

<Rates AccountRefresh = "600">

# Accepted Build Range Setup
#
# These two directives set up which clients will be
# allowed to authenticate with the realm list.
#
# Set these to the same builds that the server was
# compiled for.
#
# As of the last update, version 2.1.1 was build 6739.
#

<Client MinBuild = "6739"
MaxBuild = "7561">

# WorldServer Setup
#
# This directive controls the password used to authenticate with the worldserver.
# It must be the same between the two configs. If it is not, your server will
# not register.
#
# Default: "change_me_logon"
#

<LogonServer RemotePassword = "ascent">

Step 4
*********************************************************
Ok change this part.......
<Client MinBuild = "6739"
MaxBuild = "7561">

Step 5
*********************************************************
To this......
<Client MinBuild = "6739"
MaxBuild = "7800">
Now Save and close it...

Step 6
*********************************************************
Now if your server wasn't on when you were doing this then just start all the programs by the control panel but if it was then you need to close all 4 programs and start them again.

Step 7
*********************************************************
Ok now you should be able to enter the server with patch 2.3.2 and if you have any problems post them below.Thanks

[project anthrax]

can you still use the 2.3?

[Politz]

didn't work

[Jekuli]

Yea this worked. got my wow from 3.3 to 2.3.3 but now i get DC after loading screen -.o

[kingman]

dosent work broo.... i think need new ascent compile

[Troh]

Yea this worked. got my wow from 3.3 to 2.3.3 but now i get DC after loading screen -.o

same here, some help plz?

[kuy]

same here, some help plz?

Also yeah you will be able to log in with 2.3.0 and also make sure the top one is 6739 and if it still doesn't work try puting in 7741 for patch 2.3.2:wave:

[Tane]

I dont understand it

[Tane]

i downloaded an ascentcdb to update my ascent how do i update it with it?

[cowchmonkey]

just change it to 9999 it works to

[kingman]

dude it wont work unless u get new ascent compile.....

[LordJedi]

no i know if u get dc after 1 sec ur db is old its sucks

[LordJedi]

guys u need new db for 2.3.3

[LordJedi]

or 2.3.2 patch

[guldkorn]

i also disconnect after loading screen wtf could it be ?